Skip to main content

Intro

There are four ways to protect a wall panel or tablet with Always-On Display on:
  • Admin code protects against people near the device: it stops them from changing its settings.
  • Network security keeps wall panels on a network of their own, separated from the devices people use every day.
  • USB Debugging, turned off, stops a computer plugged into a wall panel from controlling it.
  • Limit what a device can do shows each device only the accessories it needs.

Admin Code

Anyone near a wall panel or tablet with Always-On Display on can open Settings. To stop people from changing settings, you can set up an admin code.
The admin code makes a device harder to change, but it isn’t a complete lock. For a device in a shared or public space, like a reception, a holiday rental or a home with guests, also:
  • Set it up as a control panel, so it can’t change the accessories or open the property’s admin settings. See Control Panels and Device Groups.
  • Lock the tablet to Zendo, so nobody can open other apps or the tablet’s own settings. On an iPad or iPhone, use Guided Access.
  • Keep it on its own network, for example a separate VLAN (virtual LAN), so no other devices can reach it. For a wall panel, see Network security.
  • Turn off USB Debugging on a wall panel with a USB port, so a computer plugged into it can’t control it. See Turn off USB Debugging.

Set, change or remove the admin code

  1. Tap
  2. Tap “Settings”
  3. Tap “Device Settings”
  4. Tap “Admin Code”
  5. Tap “Set Code”, choose 4, 6 or 8 digits, then enter the code twice.
To change or remove it, do the same and tap “Change Code” or “Remove Code”. You’ll need the code to open Settings first.

Good to know

  • Wrong codes: after a few wrong tries, the keypad waits a little before the next one, up to a minute.
  • One property only: a device with an admin code can’t join another property.
  • Always-On Display can’t be turned off while a code is set.
  • Not the screen lock: the screen lock PIN covers the whole screen. The admin code only covers Settings.
  • See which devices have one: if an installer set up Zendo at your property, “Control Panels” shows whether each device has an admin code, even while the device is offline. See Check a device’s details.

Forgot the admin code?

Your hub keeps a copy of each device’s code, so an admin of the property can look it up in Zendo, even while the device is offline. On your phone or tablet:
  1. Tap
  2. Tap “Settings”
  3. Tap “Control Panels”
  4. Tap the device
  5. Tap “Admin Code”
From there you can also set a new code, or turn the code off, while the device is online and has the latest version of Zendo. If your hub doesn’t have the code and your device is online, set a new code from Zendo, as above. If your wall panel is offline, please contact your installer to reset the code. For phones and tablets, please reinstall Zendo.

Network security

Connect wall panels to their own network, such as a VLAN (virtual LAN) or a separate network for the devices you install and manage, rather than on guest Wi-Fi or a network that residents, staff, tenants or visitors use.
A Zendo wall panel has network features that allow you (or your installer) to connect to it and change its settings. To stop anyone else from doing that, connect it to a network you manage. The panels’ network only needs to reach your hub (Home Assistant/Homey) and the internet. To add a panel to Zendo, the phone or tablet you pair it from must be on the same network as the panel. Connect to the correct network while you pair.

Give each device its own Wi-Fi password

If your network equipment can do this, give each device a Wi-Fi password of its own. Many business access points and some home ones can, under names such as Private Pre-Shared Key (PPSK), iPSK, MPSK or DPSK. If a device is stolen, you delete its password, and every other device stays connected. If your equipment can’t do this, use a password for the panels’ network that you don’t use anywhere else. If a device is stolen, you then only change the password on that network.

Turn off USB Debugging

If people can reach a wall panel’s USB port, for example in a reception or a holiday rental, turn off USB Debugging, so a computer plugged into the port can’t control the panel. It’s on until you turn it off.
  1. Tap
  2. Tap “Settings”
  3. Tap “Device Settings”
  4. Tap “Zendo Launcher”
  5. Tap “Advanced Settings”, then enter the admin code if you’ve set one
  6. Tap “USB Debugging”.
It takes a few seconds. The line under “USB Debugging” says whether it’s on or off. To turn it back on, tap “USB Debugging” again.

Good to know

  • Admin code: set one too. Without one, anyone at the wall panel can turn USB Debugging back on. See Admin code.
  • Installers: while it’s off, you or your installer can connect to the wall panel over the network, but not with a cable.
  • Network: this only covers the USB port, so also keep the wall panel on a network of its own.

Limit what a device can do

A wall panel or tablet that stays at your property doesn’t need to control everything.
  • Show only what each device group needs, with Family Sharing (Access Control). A panel at reception may not need the alarm, and a tablet in the hallway at home may not need the bedroom lights. See Choose what a device group shows.
  • On Home Assistant or Homey, sign in to each wall panel and shared tablet with a user of its own. You can then remove that user if the device is stolen, without changing your own login.

If a wall panel or tablet is stolen

Do these in order, as soon as you can, from your own phone or tablet. The steps are the same if a device is lost.
  1. Lock or erase it, if it’s a phone or tablet. Use Find My on an iPad or iPhone, or Find Hub on an Android tablet. A wall panel doesn’t have these services.
  2. Delete the device. For a device in a device group, see Remove a device or delete a setup link. For a person’s phone or tablet, see Remove a device. The app on it stops working straight away.
  3. Remove the device’s login from Home Assistant/Homey. If it has a user of its own, remove that user.
  4. Stop it from joining your Wi-Fi. If the device has a Wi-Fi password of its own, delete it. Otherwise, change the password of the network the device used, then reconnect the other devices on that network.
  5. Change any admin code it shared. If another device uses the same admin code, set a new one: in “Control Panels”, tap the device, then tap “Admin Code”.
  6. Check for anything you don’t recognise. In “People & Invitations” and “Control Panels”, delete any device, invitation or setup link you don’t recognise. Then check the history in Home Assistant/Homey for activity you can’t explain.
  7. Set up a replacement. See Replace a Device. The new device takes the old one’s place in your automations and flows, and “Replace a Device” lists devices you’ve deleted.
If the device turns up later, add it again with Add Device.

If an admin’s phone or tablet is stolen

An admin’s device can do more than other devices: it can see every device’s admin code, invite people, and add devices. So do these as well as the steps above:
  1. Delete it from another admin’s device. If no other admin can do this, install Zendo on another phone or tablet, and use account recovery to get a new activation link by email.
  2. Change your hub password and delete the credentials of the stolen device. See Delete the credentials of a stolen device.
  3. Change every admin code, not only the ones it shared: in “Control Panels”, tap each device, then tap “Admin Code”.
  4. Check who has access. In “People & Invitations”, check the people, devices and invitations. In “Control Panels”, check the devices and setup links.

Delete the credentials of a stolen device

  1. In Home Assistant, open the profile.
  2. Select Security.
  3. Change your password.
  4. Under Refresh tokens, delete the login the stolen device used.
You don’t need to delete the stolen device’s “Zendo” token yourself: deleting the device from “People & Invitations” deletes it automatically. Please leave the other “Zendo” tokens under Long-lived access tokens as they are. Deleting them by hand can sign out your other devices. See Tokens in Home Assistant.
Change your Homey account’s password, and ask Homey support to end the login on the stolen device.